Hydraulic Directional Control Cartridge Valve Sealing Ring 5 Controls - China

AAK control the sealing ring of Hydraulic Directional Control Cartridge Valve from 5 aspects, ensure 18 months of service life without worry Nestor is from Greece.

He has been purchasing hydraulic cartridge valves for 3 years smoothly.

A hydraulic directional control cartridge valve bothered him recently.

At the beginning of last year, the hydraulic directional control cartridge valve he purchased had leakage, which led to the loss of pressure in the oil circuit of the system.

The root cause was the wear of the sealing ring.

The original hydraulic directional control cartridge valve manufacturer said that the sealing is a standard O-ring and a single-side PTFE retaining ring, which is an industry standard.

If there was a leak, it could only be replaced.

It was not acceptable to replace it within 6 months.

Nestor realized that this cartridge valve manufacturer was unreliable.

Nestor found AAK hydraulic cartridge valve website on Google, noticed several AAK cases about the sealing ring, and left us a message: Can the sealing ring of each hydraulic directional control cartridge valve be guaranteed to be free of wear for 1 year under the high pressure of 350bar? After communication, I learned that he had a problem with the sealing ring of the hydraulic directional control cartridge valve.

I replied that regarding the sealing ring, not only the medium but also the material, shape, structure and installation should be considered.

Only 5 aspects can be considered comprehensively to determine the most suitable sealing ring.

Blind copying of industry standards may lead to leakage.

Nestor required AAK samples.

After 30 days, AAK sent 20 samples of hydraulic directional control cartridge valves.

Last week, Nestor sent an email to inform us that AAK hydraulic directional control cartridge valve has been used for 13 months without any customer complaints about leakage.

I told him that there would be no complaints in another half a year.

This hydraulic directional control cartridge valve, AAK matches the sealing ring from 5 aspects, and does not follow the industry standard.

The sealing ring of AAK hydraulic directional control cartridge valve has unique skills.

The outer circumference of the main sealing lip is installed on the inner wall of the valve hole, which reduces the contact area between the sealing structure and the valve hole, reduces the friction between the sealing structure and the valve hole, and increases the service life by at least 2 times.

The support ring can reduce the dependence of the hydraulic directional control cartridge valve sealing system on the retaining ring, and avoid the possibility of damage due to improper installation of the retaining ring.

1 - Polyurethane material is selected to replace the original rubber material.

The plane projection of the sealing ring is circular, and the middle part is a set hole.

The inner wall of the sleeve hole is smooth and fits at the bottom of the sealing groove of the hydraulic directional control cartridge valve.

High in the middle, low at both ends, symmetrical structure.

2 - The shape of the seal ring is high in the middle and low at both ends.

It has a symmetrical structure, left, middle and right.

The left and right parts have high-strength support rings, and the middle part is the main sealing lip.

3 - The support ring makes the cross section of the seal ring in "D" shape, avoiding the possibility of the seal ring being cut by the valve hole during the installation of the hydraulic directional control cartridge valve.

AAK hydraulic directional control cartridge valve, sealing ring is controlled from 5 aspects, ensure 18 months of service life without worry, you can also try it! AAK HYDRAULIC CARTRIDGE VALVES (532) 2023-03-16

Company Contact:

• Posted By: AAK INDUSTRY CO.,LTD.

• Phone: 86-574-83008115

• Address: Bona Building, No. 456 Taikang Middle Road, Yinzhou, Ningbo, China, NINGBO , ZHEJIANG , China

• Email:

• Website: https://www.aakindustry.com/

• Business Description: Hydraulic valve manufacturer, focused on the Development and Manufacturing of Hydraulic Cartridge Valves since 2006, in Ningbo China
  
  Since its establishment 12 years ago, 6 first-line international brand importers have placed orders with AAK for 5 consecutive years, with a re-peat order rate of 62%.
  
  Exported to more than 20 countries, AAK Hydraulic Valves used on "AIRCRAFT" have been supplied to Russian customers.
  
  68%+ of the high precision hydraulic valves exported from Ningbo Port come from AAK hydraulic valves.
  
  Our Products:
  
  - Hydraulic Relief Valves Dust Free Packaged For Food Equipment
  
  - Hydraulic Needle Valves 450bar Over 1 Year Service Life
  
  - Hydraulic Pilot Operated Relief Valves Benchmarked With German Hawe
  
  - With Temperature And Gain From Aak Hydraulic Valves
  
  - Hydraulic Valve Blocks Free Of Oil Leakage