Y Strainers To Protect Pumps Meters Control Valves Steam Traps - India

Y-Strainer Application Information

Y-Strainers are devices for mechanically removing unwanted solids from liquid, gas or steam lines by means of a perforated or wire mesh straining element.

They are used in pipelines to protect pumps, meters, control valves, steam traps, regulators and other process equipment.

Y-Strainers are very cost effective straining solutions in many applications.

Where the amount of material to be removed from the flow is relatively small, resulting in long intervals between screen cleanings, the strainer screen is manually cleaned by shutting down the line and removing the strainer cap.

For applications with heavier dirt loading, Y-Strainers can be fitted with a 'blow-off' connection that permits the screen to be cleaned without removing it from the strainer body.

Y-Strainers are used in a wide variety of liquid straining applications to protect downstream process system components in many industries, including: chemical processing, petroleum, power generation and marine.

Water handling applications, where Y-Strainers are used to protect equipment that could be damaged or clogged by unwanted sand, gravel or other debris, are very common

While often used in many different types of liquid applications, a Y-Strainer is considered the standard for steam applications and is almost universally used for these applications.

Its compact, cylindrical shape is very strong and can handle high pressures.

It is, literally, a pressure vessel.

Y-Strainers which handle pressures up to 6000 psi are not uncommon.

Of course, in these cases, the design of the strainer is critical so that it can stand up to these high pressures without fear of failure.

When high pressure steam is being handled, another complicating factor arises, temperature.

With steam pressures of 1500 psi or higher, standard carbon steel is sometimes not suitable because the steam temperature may be 1000° F or higher.

In these cases, the Y-Strainer body is generally made of chrome-moly steel.

Besides steam,

Y-Strainers are often used in air and natural gas applications.

Here again, high pressures are not uncommon.

However, unlike steam high air pressure does not automatically mean high temperature and so, ordinary carbon steel bodies of sufficient wall thickness will generally suffice.

Unlike other types of strainers, a Y-Strainer has the advantage of being able to be installed in either a horizontal or vertical position.

Obviously, in both cases, the screening element must be on the 'down side' of the strainer body so that the entrapped material can properly collect in it.

Some manufactures reduce the size of the Y -Strainer body to save material and cut cost.

Before installing a Y-Strainer, be sure it is large enough to properly handle the flow.

A low-priced strainer may be an indication of an undersized unit.

Carbon steel Y-Strainers are used mainly in the oil and petrochemical industry.

They have excellent resistance to mechanical or thermal shock and these are important consideration in the event of a fire.

Most oil refineries will not permit iron piping components for this reason.

Carbon steel Y-Strainers are also used for higher pressure applications because of their great strength.

Stainless steel Y-Strainers are used where high corrosion resistance or where freedom from contamination is required.

They are popular in the chemical, food and pharmaceutical industries.

It cannot be stressed too highly that Y-Strainers for critical applications must be adequately designed.

This means sufficiently heavy wall thickness and blow-off connections.

As an example, in improperly trapped steam lines, condensate can collect in low points and become a slug of water traveling at very high velocity down the line.

Even the slight change in direction caused by a Y-Strainer can produce a tremendous shock which can damage the strainer.

Manufacturers who thin down walls to save weight and cost are asking for trouble in these cases.

A Y-Strainer, if fitted with a blow-off connections, can be a self-cleaning strainer.

A valve is installed on the connection located on the strainer cap.

The screen can thus be cleaned by simply opening and then closing the valve without shutting off the flow or disassembling the strainer.

When the valve is opened the material trapped inside the screen drains out.

The illustration above show a Y-Strainer with a blow-off connection.

Another critical thing to check for in Y-Strainers is the point where the screen or straining element seals to the body.

This seat should be carefully machined so no particle can bypass it.

The same thing applies to the cleanout end.

The screen should fit tightly.

Beware of strainers with un-machined seats.

The improperly seated screen will permit bypass of the fluid allowing dirt or debris downstream.

Y-Strainers are available with a wide variety of end connections including threaded, flanged and welded.

Flanges are designed to ANSI specifications.

Special flanges such as ring joints are often available as well.

Y-Strainers can be constructed to US Navy flange dimensions, which are different from commercial standards.

For extremely high pressure applications, Y-Strainers with socket or butt weld end connections are often specified.

When specifying or buying a Y-Strainer, price, which is often the prime consideration, should be the least important consideration.

A well made and properly designed Y-Strainer will last almost indefinitely.

Its first cost is, therefore, not important compared to other features when spread out over a service life of many years.

Company Contact:

• Posted By: CHAMPION SCREENS MANUFACTURING COMPANY

• Phone: 918571231755

• Address: 1-32, OPPOSITE GMR POLYTECHNIC COLLEGE,NIMMANAPALL, MADANAPALLI , India

• Email:

• Website: https://wedgewirescreens.co.in

• Business Description: Champion Screens Manufacturing Company is a subsidiary of Champion
  
  Filters Manufacturing Company A 3 decade old organization specialized
  
  in design & manufacture of all types of Automatic Filtration &
  
  Screening Systems.
  
  Champion Screens produces wedge wire screens for virtually all screening applications.
  
  We have separate wedge wire screen making machinery for cylindrical screens & flat panels.
  
  We have the capability to produce screens as large as 4 meters in diameter X 6 meters length in one single piece construction.
  
  Wedge wire flat panels are made on flat panel manufacturing machine.
  
  So we can offer a truly flat panel instead of a re rolled slit cylindrical screen.
  
  Needless to say this offers better screening efficiency and better dewatering ability.
  
  Champion Screens have full fledged wedge wire manufacturing plant in house.
  
  Wedge wire (Vee Shaped or V wires) are manufactured in house.
  
  There are no limitations of size or shape of wedge wire.
  
  We can make vee shaped, v shaped, triangular shaped, trapezoidal wedge shaped, rectangular wedge, drop shaped wedge , wedge wires in any profile for optimum production.
  
  Cylindrical wedge wire screens are made by wrapping a wedge shaped (v shaped) wire on a cage of longitudinal rods.
  
  Each & Every intersection of this wedge wire & beneath support rods is welded.
  
  We make vee wire screens from Low carbon steel wedge wire, Stainless Steel grade 304 wedge wire, Stainless Steel AISI 316 wedge wire, Duplex Stainless Steel Wedge Wire, Super Duplex Stainless Steel Wedge Wire.
  
  We make wedge wires from wires as small as 0.25mm diameter to 18mm width & above if required.
  
  Please email us at championscreens2012@gmail .
  
  com for more information.
  
  Screens Cylinders made from trapezoidal wire wrapped filter screen