Ae Series Off Gas Preheating Continuous Feeding Equipment - China

AE series preheating continuous feeding equipment is the most advanced,

clean, energy saving and environmental protection metallurgy off gas

using equipment in nowadays.

This is using the off gas from the electric

furnace to preheat the raw materials, and avoided the high failure rate,

complicated operation, can not charging materials continuously and other

weakness from Shaft furnace preheating and preheating bucket and other

traditional ways.

This system has been put into production in more than

20 factories in China and several other countries.

And had gain marked

affects in electricity saving, energy saving, production increasing,

pollution reduction, and brought great economic benefits for customers.

AE series preheating continuous feeding equipment has characteristics of continuous feeding, continuous melting, continuous smelting and others, which advantages are: smelting period is short, low power consumption, low noises, low investment cost and etc…

Comparing with the traditional EAF, the technical index of continuously preheating and feeding EAF process are:

1 - Production capacity increases more than 10% .

2 - Smelting cycle is shortened by 10- 15 Min.

3 - Save energy of 100- 120kw.

h/ t for per ton Steel.

4 - Electrode consumption decreases by 0.5- 0.8% , Refractory material consumption reduces by 5% .

5 - 20- 30% reduction of CO2 volume which is released from per ton of Steel; Production site dustiness is less than 10mg/ M3.

6 - Dioxin and CO emissions meets relative emission standards, Flue gas and dust are decreased from 17kg/ t to 11kg/ t.

7 - Fully utilization of waste heat: On the Conveyor section can preheat the materials up to 300 degree Celsius and higher, and add burner in conveyor section that can raise the materials up to 600 degree Celsius.

The rear part of the waste heat can be used to generate electricity or heating by steam which is produced by waste heat boiler, the gas from the boiler basically can go into the bag type dust collector directly.

But the traditional electric furnace system off gas must go through the water cooled pipes, air forced cooler and other equipments, it will consume much energy to cool the temperature down and then put the gas into dust collector, so waste the energy from the off gas.

8 - De- duster Fan power reduces 30% .

9 - Noise is fewer than 90 decibels during the electric furnace smelting cycle.

Company Contact:

• Posted By: Xi'an Abundance

• Phone: 862989388771

• Address: Tang yan road, Xi'an , China

• Email:

• Business Description: Xi an Abundance Electric Technology Co., Ltd is located in Xi an, which is the research base of electric furnace industry and the national supervision and inspection center of electric furnaces in China.
  
  With the development of 15 years, it has become a leading manufacturer in China s electric furnace industry, and it is advanced in R&D, manufacture, installation, debugging and technical services.
  
  There are our agents and after sale services in South Africa, Egypt, the Middle East, Mexico and Ukraine.
  
  Hundreds of sets of our electric furnaces are working safely now all over the world.
  
  That s why 90% of our products are exported to more than 50 regions and countries worldwide, and our achievements in furnace exportation ranked in the forefront for three consecutive years among furnace industry.
  
  Xi an Abundance Electric Technology Co., Ltd has a strong power in R&D, and more than 200 staffs are working here, among them, 3 senior engineers are specialized in researching and developing the metallurgical equipment, 3 national senior metallurgy experts, 12 engineers and assistant engineers, 8 senior skilled technicians on the production line and more than 30 production technology backbones and senior management.
  
  This high quality team makes us to be a professional manufacturer in the field of metallurgical machinery equipment, from design, manufacture to marketing.
  
  We have hundreds of successful cases in designing and producing the whole set of equipment, such as Electric Arc Furnace (EAF), AE Series Off Gas Preheating Continuous Feeding Equipment, Ladle Refining Furnace (LF), Submerged Arc Furnace, AOD Argon Oxygen Decarburizing Furnace, Basic Oxygen Furnace (BOF), Based on the market demand, Dedusting Equipment of electric furnace, Static Var compensator（SVCï¼⠀°.
  
  We always insist on our principle of optimizing our product features, saving our customer s cost and assuring the high quality of the product.
  
  Consequently, we have won the customers favor and ratification on our products and after sale service.
  
  Xi an Abundance Electric Technology Co., Ltd has passed ISO9000 authentication of international quality management system and European CE certification.
  
  We have got 6 national patent certifications in the professional field.
  
  With our strong economy, scientific and technological strength, strict attitude, advanced way of designing, integrity of business ideas and perfect after sale services, we sincerely serve the world's metallurgy, forging, casting, military, automotive, agricultural machinery, motorcycle, aerospace, marine, hardware tools, general machinery, heat treatment and other industries.