Liquid Molding Silicone Rubber For Cornice Molds - China

APPLICATIONS of Platinum molding silicone rubber for cornice molds:

Platinum molding silicone rubber for cornice molds mainly used for making concrete stones, precision molds, PU molds, resin molds, gypsum casting, candle molding, for life casting, fabric finishing, seal for electronic components and solar circuit board, trademark decoration.

etc.

FEATURES of Platinum molding silicone rubber for cornice molds

Two- parts, flowable liquid silicon & curing agent.

Can solve the problem of not lighting of the candles and the problem of sticky and white stains on the surface of cement & stone products.

Good tensile strength and tear strength, low shrinkage.

It gets cured at room temperature 25 0C within 5- 7 hours.

An exceptional fluidity and good operability, easy to be demolded.

Suitable for pouring methods of operation for small sized molds making.

Datasheets of Platinum molding silicone rubber for cornice molds

Product E- 620

Appearance Translucent

Hardness( shore A) 20±2

Mix ratio( A: B) 1: 1/ 10: 1

Viscocity Part A( mPa.

s) 23000±2000

Viscocity Part B( mPa.

s) 3500±500

Tensile strength ( kgf/ cm2) 45±5

Tear- strength ( kN/ m) 20±2

Elongation( % ) 500±50

Pot life/ working time ( mins) 30- 40

Curing time/ setting time ( hrs) 3- 4hrs( 25°C)

110- 20mins( 60°C)

Shrinkage rate ( % ) 0.1

DESCRIPTION of Platinum molding silicone rubber for cornice molds

Platinum molding silicone rubber for cornice molds is generally named two- components silicone rubber, Part A and part B.

It features an exceptional fluidity and good operability.

The mixing ratio is 1: 1, mainly be suitable for making molds application.

E640# addition cure silicone rubber is mainly used for molds making for food grade products.

And it is also develop to solve the problem of not lighting of the candles and the problem of sticky and white stains on the surface of cement & stone products.

OPERRATING INSTRUCTION of Platinum molding silicone rubber for cornice molds

1 - Stir part A and part B with right mixing ratio

evenly.

And get the mixture for vacuum-

pumping.

( If there is no vacuumizer, you can just pour the mixture slowly from the corner so that less bubbles caused) .

2 - Enclose the product ( the original model) with four plastic plates or wooden plates.

3 - Clean your products and brush a layer of release agent( detergent or soap water) on your product.

4 - Pour the mixture with correct mixing ratio into the model frame.

After about 2- 4 hours, when the silicone cured, get out the original model, and there you get a finished addition cured silicone mold .

SHELF LIFE of Platinum molding silicone rubber for cornice molds:

Twelve ( 12) months from date of shipment when stored at 24°C in original unopened packages.

PACKAGE of Platinum molding silicone rubber for cornice molds

Packed in clean 00kg/ pail.

Company Contact:

• Posted By: SHENZHEN HONG YE JIE TECHONOLOGY CO; LTD.

• Phone: 8675589212380

• Address: Building 4, No.6 Laiying Road, Xin Sheng Long Shan, Shenzhen , China

• Email:

• Website: http://www.szrl.net

• Business Description: TCC Silicone Co., Ltd. was established in 1998, is a Science and
  
  technology corporation which is engaged in production, R & D, and sales
  
  of silicone rubber.
  
  It sets up Hong Kong Hongye Ltd., Shenzhen Hongye
  
  silicone rubber Factory and other affiliated enterprises in 2005.
  
  Our products including 36 series in hundreds of kinds of silicone products like silicone rubber, RTV 2 molding silicone rubber, silicone rubber for manual model design, shoe sole mold silicone rubber, silicon oil, pad printing silicone rubber, encapsulant and potting compound, silicone rubber for LED display, electronic thermolysis ointment, thermal conductivity silicone, special silicone rubber for CPU, silicone tube, silicone membrane, silicone sealant , liquid silicone rubber, addition cure RTV silicone rubber, HTV silicone rubber, solid silicone rubber, gross rubber, silicone rubber sheet, hot stamping silicone plates, hot stamping silicone roller, etc.
  
  These are currently been exported to Southeast Asia, Europe, the America and other 50 countries and regions.
  
  To reach the internationally leading quality standard with competitive price is our permanent pursuit.
  
  We aim at supply high quality products to meet customers' satisfaction.
  
  It is our solemn commitment that any of our products with quality problems will be replaced within 3 months after purchase.
  
  We offer on site follow up service for product demonstration, free customer service to solve technical issues, free mold opening technologies, free technical training on pad printing silicon usage and rubber head making.
  
  What you need is what we pursue.
  
  We are committed to back you up in producing first class products.
  
  Welcome old and new customers and distributors anywhere around the world to negotiate for business and co operations.
  
  Let's join hands and strive for mutual prosperity!