Injector For Sale 33408 Mitsubishi Fuel Injectors Replacement - China

injector for sale 33408 mitsubishi fuel injector replacement

A common rail is one of the most important components in a diesel and gasoline direct injection system.

The main difference between a direct and a standard injection is the delivery of fuel and the way how this one mixes with incoming air.

In the direct injection system, the fuel is directly injected into the combustion chamber, skipping the waiting period in the air intake manifold.

Controlled by the electronic unit, the fuel is squirted directly where the combustion chamber is hottest, which makes it burn more evenly and thoroughly.

The main advantages of the common rail direct fuel injection can be summarized in reduction of exhaust and noise emissions, better fuel efficiency and improved overall engine performance.

The system consists of a high-pressure pump, injectors, a rail, and an electronic control unit.

Common rail Injector as one of most important components in common rail injection system, It is an accessory that must be replaced at high frequencies in the system.

CHINA-LUTONG is specialize in providing high quality common rail injectors.

The merits of the common rail fuel injection system architecture have been recognized since the development of the diesel engine.

Lower fuel pump peak torque requirements.

As high speed direct injection (HSDI) engines developed, more of the energy to mix the air with fuel came from the fuel spray momentum as opposed to the swirl mechanisms employed in older, IDI combustion systems.

Only high pressure fuel injection systems were able to provide the mixing energy and good spray preparation needed for low PM and HC emissions.

To generate the energy required to inject the fuel in approximately 1 millisecond, the conventional distributor pump would have to provide nearly 1 kW of hydraulic power in four 1 ms bursts per pump revolution, thus placing considerable strain on the drive shaft.

One of the reasons behind the trend toward common rail systems was to minimize the maximum pump torque requirement.

While the power and average torque requirements of the common rail pump were similar, high pressure fuel delivery is to an accumulator and thus the peak flow rate (and peak torque required to drive the pump) does not have to coincide with the injection event as is the case with the distributor pump.

Pump discharge flow can be spread out over a longer portion of the engine cycle to keep pump torque demand more even.

Improved noise quality.

DI engines are characterized by higher peak combustion pressures and, thus, by higher noise than IDI engines.

It was found that improved noise and low emissions were best achieved by introducing pilot injection(s).

This was most easily realized in the common rail system, which was capable of stable deliveries of small pilot fuel quantities over the entire load/speed range of the engine.

#injector assembly diesel# #INJECTOR ASSEMBLY JOHN DEERE# #Injector Assy# #injector assy fuel# #injector assy toyota# #injector bosch diesel# #injector china # #injector components# #injector cummins diesel# #injector diesel# #injector diesel pump# #injector experts# #injector factory# #injector for dodge diesel# #injector for sale # Below is some of high quality common rail diesel injector for sales on the market: Injector NO: Engine

0 445 120 007 Cummins ISBe

0 445 120 212 Cummins ISBe, EEA

0 445 120 238 Cummins

0 445 120 255 Cummins(USA)

0 445 120 059 Cummins SAA6D107E-1

0 445 120 121 Cummins ISLe_EU3

0 445 120 122 Cummins ISLe

0 445 120 123 Cummins ISLe4 cyls, 6 cyls

0 445 120 125 Cummins PC359-7, QSL9

0 445 120 133 Cummins QSL8.9 E-mail: fuelinjectionparts @ hotmail.

com

WhatsApp: +861366693197 0

QQ : 2850613608

NV GAO

Company Contact:

• Posted By: China-Lutong Parts Plant

• Phone: 13666935270

• Address: Xinhan Industrial Zone, Hanjiang District, Putian , fujian , China

• Email:

• Website: http://www.china-lutong.com

• Business Description: China Lutong Parts Plant manufactures fuel Injection including EFI (Electronic Fuel Injection), CR (Common Rail Fuel Injection) and High-Pressure Pumps (HPP).
  
  All China-Lutong fuel Injection products released to the aftermarket are OE fit, form and function, and are produced to OE specifications, get the new standard in fuel injection with China-Lutong fuel injection kits and EFI systems.